Saturday, November 9, 2013

Bias tube method for making binding

IMG_7045I have seen a few blog posts recently about binding. Most of the discussions recommended cutting strips and joining them individually with diagonal seams. I prefer to make binding using the bias tube method and avoid lots of marking, pinning, pressing individual seams and clipping dog ears.  Unlike other posts I’ve seen about this technique, I don’t use scissors or mark any cutting lines.  Here’s how I do it.

Tools

  • rotary cutter, ruler and mat
  • iron and pressing surface
  • pins
  • Quilter’s Strip Ticket (optional, see below)
  • corner trimming template (optional)

The following two tools make things easier, but they aren’t essential.

IMG_7087 IMG_7086

Tool #1 :To figure out what size square of fabric to start with for the amount of binding I need, I turn to my handy-dandy “Quilter’s Strip Ticket”.  Besides instructions, it has tables listing what size squares to use to make various amounts of binding of various widths.  This was one of my better quilting tool purchases, well worth the $6.00 it cost me.  You can find it by doing a web search for it.  Alternatively, I have wrestled with the geometry and done the math and I can email you the really ugly equations you can plug numbers into if you are so inclined.  The ready made tables are much handier though!

IMG_6795

Tool #2: This corner trimming template helps me line up points with edges just right, but as I managed for years before acquiring the template, I can safely say you can use this bias tube method without trimming points with the template. 

Here we go:

IMG_6982

1. Start with a square.

IMG_6984

2. Fold the square in half on the diagonal and press the fold.  This creates a guide to cut along in the next step if your ruler isn’t long enough to reach across from corner to corner.

IMG_6986

3. Cut the square in half diagonally .

IMG_6987

IMG_6989

4. If you have a corner trimming template (mine is Marti Michell’s corner trimming template) trim the 45 degree tips of the two resulting triangles.  Trimming here will make everything easier to line up in step 6.

IMG_6992

5. Arrange the trimmed triangles as shown above, with the right side of the fabric facing up.

IMG_6995

IMG_6997

6. Now flip the triangle on the right, top to bottom, turning the fabric wrong side up. The edge that was on the bottom will now be at the top, lined up with the top edge of the other triangle, right sides of the fabric together .  If you trimmed the triangle tips earlier you will find that the trimmed tips line up perfectly with the 90 degree corners as shown in 6b. Join the matched edges with a 1/4” seam.  Press seam open.

If you do not have a corner trimmer, line up your pieces as shown in the following diagram.

alternative to corner trimming 2

IMG_7002

7. Lay out the resulting diamond, fabric wrong face up, with the seam oriented as shown above.

IMG_7006

8. Measure the desired width of the binding as shown above. Measure from the bias edge.

IMG_7008

9.  Make a cut about 6 inches long.

IMG_7010IMG_7011

10.  If you have a corner trimmer, trim the point as shown. Again, you don’t need to trim, but it would make things easier in step 14.

IMG_7013

11.  Flip the fabric right side up,  with the cut dangling strip away from you as shown above.

IMG_7014

12. Fold the left hand point to the right. 

IMG_7015

13.  Fold the right hand point to the left.

IMG_7016

IMG_7018

14. Pin the edges that meet in the center.  The point formed when you made that dangling strip will be at the top left corner.  If you trimmed this point in step 10, it will line up nicely (14b) and you won’t have to guess how much to offset it to allow for the seam allowance.  The lower right hand corner will look like photo 14c below.

IMG_7020

 

IMG_7021 15.  Sew the center seam with 1/4” seam allowance and press the seam open.

IMG_7022

16.  Turn the tube right side out.

IMG_7024

IMG_7028

17. Now go back to that dangling strip you started in step 9.  Starting where you stopped cutting in step 9, measure the correct width and continue the cut, being careful to keep the rest of the fabric tube out of the way of the rotary cutter. 

IMG_7030IMG_7032IMG_7033

18. Roll the fabric tube and continue cutting the strip.  Repeat and keep cutting until you reach the end.

IMG_7034

19. You now have one long bias strip.

IMG_7036IMG_7037

20.  Fold the strip in half lengthwise, pressing the fold as you go.

IMG_7045

21.  Ta-da!  Lots of bias binding to bind your lovely quilt.  This particular length of binding is going to bind Quilter’s Scrapbook tomorrow.

8 comments:

  1. I have tried that method in the past, but it didn't work very well for me. After studying your great tutorial, I'll probably try it again. Thanks for showing the steps very clearly! ---"Love"

    ReplyDelete
  2. That looks like something I could really mess up! But I do have a better understanding of what people mean when they say "tube method" now, so maybe one day I'll be brave enough to try it this way.

    ReplyDelete
  3. Great tutorial. I have saved it for future reference!

    ReplyDelete
  4. I love using this method. I can't believe some quilters don't use bias binding. If only they knew how much easier it is to use and it looks so much better.

    ReplyDelete
  5. I never knew it was done that way. I think I should try it sometime. When I have used bias binding, I just cut a large diagonal section and kept cutting off of the triangle, not knowing if I would have enough or need to cut more. I see that being able to cut a square piece would be less wasteful in the long run. I would definitely need the "Strip Ticket." I've never seen that before. Thanks for demonstrating this.

    ReplyDelete
  6. The best tutorial! EVER!

    Thank you!

    ReplyDelete
  7. Excellent! I've always wanted to try this. Your tutorial is great!

    ReplyDelete
  8. Great and crystal clear tutorial! This is a much needed refresher course for me as I couldn't remember how to do it. Thanks bunches! Amie

    ReplyDelete

Thank you for visiting. I truly appreciate your comments and will try to reply to comments by email if your commenting staus is not set to "no-reply".

If you have a question, emailing me directly at joanne@canuckquilter.com will ensure I have your address to respond. I promise I will not share your email address and I will not use it for any purpose other than replying to your message.